Other Products

Scope of use: the agent is intended for manual cleaning of printing matrixes from UV colours, i. e. colours drying out due to the effect of UV radiation.

Directions for use: use the preparation as a concentrated cleaning agent, which, together with UV colour, creates an emulsion, which you will wash down with water.

Scope of use: the agent is intended for printing machine cleaning from water-soluble, acrylate-based colour in a closed cleaning system.

Directions for use: cleaning proceeds in a closed system. Dilute the cleaner with water in a 1:1 ratio and pour it in the storage tank. Upon finalizing the cycle, wash down the agent residues from the machine with water.

Scope of use: the agent is intended for defect (incompactness, crack) detection in metallic and nonmetallic materials, riveted joint tightness, rolling in of the tubes, soldering quality using the capillary method of colour indication.

Directions for use: at first, clean thoroughly the test object from mechanical impurities. It is not necessary to carry out complete degreasing. Apply sufficient amount of Indikal I (Red) on the cleaned surface of the test object using a brush or by submersion. Let it act for 5 to 10 minutes. During this period of time the layer may not dry out, thereby spread the surface over continuously. After 5 to 10 minutes, rub off the red fluid with a clean cloth and wipe off completely. Perform the rub-off and the wiping as quickly as possible so that the time between the rub-off and the white fluid application is as short as possible. Now, you may apply (using a brush, spray, soak) on the place in view a thin layer of Indikal II (White). If there are cracks in the object in view, they will come up on the surface after 2 to 3 minutes in the form of red lines or dots. The intensity of line colouring depends on the depth and the width of cracks. The latter caused by faulty steel quenching will show as a grain in the form of a mesh.

Scope of use: the agent is intended for defect (incompactness, crack) detection in metallic and nonmetallic materials, riveted joint tightness, rolling in of the tubes, soldering quality using the capillary method of colour indication.

Directions for use: at first, clean thoroughly the test object from mechanical impurities. It is not necessary to carry out complete degreasing. Apply sufficient amount of Indikal I (Red) on the cleaned surface of the test object using a brush or by submersion. Let it act for 5 to 10 minutes. During this period of time the layer may not dry out, thereby spread the surface over continuously. After 5 to 10 minutes, rub off the red fluid with a clean cloth and wipe off completely. Perform the rub-off and the wiping as quickly as possible so that the time between the rub-off and the white fluid application is as short as possible. Now, you may apply (using a brush, spray, soak) on the place in view a thin layer of Indikal II (White). If there are cracks in the object in view, they will come up on the surface after 2 to 3 minutes in the form of red lines or dots. The intensity of line colouring depends on the depth and the width of cracks. The latter caused by faulty steel quenching will show as a grain in the form of a mesh.

Scope of use: the agent is intended for transferring pressure up to 30 MPa, casting mass for picking-up fingerprints and for preparation of elastic moulds and for casting the damping blocks under vibrating and noisy machines.

Directions for use: warm up Solagel, while stirring continuously, preferably in a steam-jacketed vessel with heat-transfer fluid (oil), and, heat it as long as the melt reaches a temperature of 175・・C. When reaching a temperature of about 120・・C it will change into a gelatinous, almost pasty mass, which will gradually thin out, and, at a temperature of 175・・C it will gain a homogenous character of honey-like consistency. In this condition Solagel will be ready for casting into prearranged moulds.

Scope of use: PURUS is suitable for cleaning of paper books, book edges, including colour and goldplated ones. For leather bookbindings it is suitable with an increased caution. It is not suitable for glossy surfaces (as it forms maps).

Directions for use: dust off the books - by vacuum- cleaning. Carry out the final cleaning with PURUS using fluent strokes in one direction. PURUS will crumble away during the cleaning. Vacuum the remains. Remove continuously crumbs and dust layers formed on PURUS during cleaning.